- På rea!
HDFURY 3
No HDMI? No problem! The HDfury3 upgrades any TV or projector by adding HDMI! Works with any display that accepts either Component (YPbPr/YCbCr) or RGB/VGA! Don’t be stuck watching Blu-ray, DVD, Satellite/Cable at only 480p! Add an HDfury3 and watch hi-def at up to FULL HD 1080p resolution!x
Security policy (edit with Customer reassurance module)
Delivery policy (edit with Customer reassurance module)
Return policy (edit with Customer reassurance module)
No HDMI? No problem! The HDfury3 upgrades any TV or projector by adding HDMI! Works with any display that accepts either Component (YPbPr/YCbCr) or RGB/VGA! Don’t be stuck watching Blu-ray, DVD, Satellite/Cable at only 480p! Add an HDfury3 and watch hi-def at up to FULL HD 1080p resolution!
Why do I need HDfury3?
How old is your HDTV or projector? If it was bought before 2005 it does not have an HDMI input. This means that you’ll never be able to use the full potential of your expensive projector, plasma display, or PC screen with new sources like the PS3, Xbox360, Blu-ray players, Cable TV / Satellite boxes, or PC graphics cards at up to 1080p FULLHD resolution.
Without an HDMI input your display will be limited to 480p in most cases – that’s only 1/6th the resolution of 1080p FULLHD! You need HDfury3 to unlock the full potential of your display! Why buy an expensive new HDTV when your existing one works perfectly well? Enhance your display’s compatibly and value with HDfury3!
Designed by a group of home theater videophiles, the HDfury3 delivers a razor sharp picture with unprecedented colour from HDMI sources, supporting all resolutions up to 1080p FULL HD. The picture quality improvement when using HDfury3 is immediately obvious, providing an amazingly clear and detailed picture!
-
Blu-ray, HD DVD, and DVD players (as well as the Xbox360 and PS3) will not upscale standard DVDs to 1080p over analog outputs. They are limited to 480p output only. The HDfury3 overcomes this limitation.
-
If the Image Constraint Token (copy protection) is enabled on Blu-ray or HD DVD discs reduces resolution from 1080p to 540p (1/5th the resolution) over analog outputs. The HDfury3 overcomes this limitation.
-
And most importantly: The image quality is significantly worse over analog outputs. The HDfury3 overcomes this limitation.
HDfury3 is what you need to to add digital HDMI 1.3 to your TV to bring it into the next generation and provide the best image quality possible!
Will HDfury3 work for me?
1. Does your display support at least one of the following resolutions: 480i, 480p, 576i, 576p, 720p, 1080i, or 1080p?
2. Does it have a Component or RGB (PC/VGA) input connector? (some examples shown below)
[spaces:0][spaces:0]
Component Input |
RGB VGA style Input |
RGB 5-BNC input |
If you answer YES to both questions then HDfury3 will work for you!
What’s Included? / Which cables should I order?
Absolutely everything you need is included. You won’t need to find any of the expensive extras to get up and running. Our kits include:
- HDfury3 Component Cable: For displays with component (Y/Pb/Pr) inputs. Included with every order.
- HDfury3 RGB Cable: For displays with an RGB (VGA) inputs. Basic Kit gives you a choice of one of three RGB cables:
BLUE (VGA to VGA male): For displays with a standard female D-sub VGA style RGB connector. This is the most popular RGB input connector.
GREEN (VGA to 5-BNC male): For displays with 5-BNC input RGB connectors. Used mostly by professional displays.
RED (VGA to Barco Port 3): For Barco CRT projectors only.
The Advanced Kit includes all three.
If your display only has component inputs you will not use the RGB Cable so it doesn’t matter which you order. If your display has 5 RCA style connectors order the GREEN cable and use five BNC to RCA adapters (sold separately). - An HDfury3 power supply is required and included with all our kits. The Advanced Kit also includes a power supply for GammaX. [spaces:0][spaces:0]
US (120V/60Hz)
EURO (230V/50Hz)
UK (240V/50Hz)
- 6′ USB power cable: Part of the HDfury3 power supply.
- (ADVANCED KIT ONLY) GammaX converter: On most TVs and projectors, movies and games are too dark or missing detail in dark scenes. Gamma-X to fixes this by adding a ‘Gamma Boost’ without washing out the picture. Use the Gamma-X with the HDfury3, HDfury2, HDfury1, HDfury Gamer Edition, or any device with RGB output and enjoy a more vibrant picture with perfect shadow details!
- (ADVANCED KIT ONLY) 6′ HDMI cable: For connecting your source device to the HDfury3.
- (ADVANCED KIT ONLY) 6′ Optical audio cable: A mini-Toslink to regular Toslink/SPDIF (fiber optic) cable for connecting the HDfury3 sound output to your receiver/pre-amp.
GETTING STARTED WITH HDFURY3
1) Is HDfury3 RGBHV output compatible with my Display ? (How to make sure that your display is compatible)
If you are not sure whether or not HDfury3 is compatible with your PC Monitor, CRT Projector, or Plasma/LCD HDTVs we recommend you to perform the following test:
720p TEST
- Setup a PC computer graphic card to 1280×720 resolution (50 or 60hz depending on your location eg: US : 60hz, Europe: 50hz) through its VGA output in order to see if it displays correctly on your screen throught the VGA input (SUB-D HD15/5xBNC/DB9)
If you can see the output it means that you will be able to display 720p from any HDMI or DVI(HDCP) source on your screen using the HDfury3 RGBHV output.
1080p TEST
- Setup a PC computer graphic card to 1920×1080 resolution through its VGA output in order to see if it displayed correctly on your screen through its VGA input (SUB-D HD15/5xBNC/DB9)
If you can see the output it means that you will be able to display 1080p from any HDMI or DVI(HDCP) source on your screen using the HDfury3 RGBHV output.
It has been reported that even though some PC monitors allow higher resolutions to be displayed such as 1920×1200 it does not automatically mean that the display supports a 1920×1080 resolution.
As an example both Dell 2405FPW and Sony P234B are listed as 1920×1200 native resolution. Unfortunately the Dell one does not support a 1920×1080 resolution correctly while the Sony one will display it perfectly.
So once again, performing the above test will allow to find out if HDMI 720p or 1080p could be displayed on your screen with HDfury3 RGBHV output.
We believe that the EDID of any 1920×1200 monitor could be updated in order to support 1920×1080 resolution. More on that later.
Plasma and LCD HDTVs are oftenly listed as “Supporting 720p/1080i” or “720p/1080i compatible”.
This does not mean that these displays are TECHNICALLY ABLE to handle 1280×720 or 1920×1080 resolution !
In fact most of them are 1024×768 max resolution
Basically those displays will receive a higher resolution signal through their components or VGA input and DOWNSCALE it to 1024×768 (the best supported resolution)
The well designed (often more expensive) displays will DOWNSCALE 1280×720 or 1920×1080 through both VGA and/or component input. (Ex: Panasonic TH-42PH9WK)
However it has been reported that some do not DOWNSCALE signals sent through the VGA input but only through component !
Therefore it is best to use the above test to make sure that the HDfury3 RGBHV output will work with your display device !
2) Is HDfury compatible with my Source ?
HDfury is FULLY compatible with all recent HDMI (and/or DVI-D hdcp) source devices such as the PS3, X360 Elite, HD-DVD players, Blu-Ray players, HDMI graphics card and the latest set-top-boxes (STB) and DVD players with HDMI outputs. We recommend that a power supply be used for all sources.
3) Digital and Analog Link between HDMI Source >> HDFury3 >> Display
Straight HDMI cable: If you are experiencing problems getting a HDMI signal displayed correctly from a Toshiba HD-DVD player and you call Toshiba, the first thing they will tell you is to “Please remove any HDMI to DVI adapters in your signal path!”
You should ALWAYS use the supplied breakout (extender) cable that shipped with your HDfury3: No warranty on the quality can be given when using another breakout cable, especially cables that are longer.
4) My display technically supports 1280×720 (and/or 1920×1080) through its VGA or component input (RGBHV either 5xBNC/Sub-D HD15/DB9) and I’m using a recent HDMI source. Unfortunately I have no picture on the screen.
Once you hooked up HDfury3 to your display and ran a HDMI cable to your source the first thing you need to check is the Blue led status: Is the Blue LED ON ?
The led indicates that HDfury is receiving enough power from the DVI/HDMI source and ensures that device is now operating and outputting a signal. (by default HDfury3 is set to component output)
If LED is OFF, the HDfury is not working, and therefore no signal is going out to your display.
Reasons could be one of the following:
- Your HDMI source is not set to output through HDMI > (ex: on PS3 you must activate HDMI from the display settings)
- Your HDfury3 needs to be setup for your source/display, refer to usermanual for step by step instructions: see www.hdfury.eu by the products and go to the downloads
5) Some notes on when you first connect the HDfury3 !
When you connect the HDfury3 in RGBHV output mode for the first time you may see the screen shifted to the left > This is normal.
Simply adjust your display’s settings to shift the image back. This needs to only be done once.
On some European CRT displays you will not be able to shift back far enough because of the US/Euro HD ‘porch’ differences.
If this affects you, switch your source to 60Hz to solve the problem. You can setup a new memory and it won’t disturb any of your original settings.
As the HDfury comes unique screen adjustement method via push buttons, you can always have the H position to adjust. see www.hdfury.eu by the products and go to the downloads
For example, you can connect HDfury3 to your PC VGA screen, and you will see that the first time the picture is shifted to the left.
You can then adjust this setting on your PC display, and it will be perfect. If you connect your computer back to the PC VGA screen, the image will centered as before!
Your screen / display has memory functions to store your settings depending on the source. There is no other settings to adjust.
Enjoy ! Good times ^_^
-
HDfury3 is the world’s most powerful HDCP deciphering converter ever built! Introducing new features such as two HDMI 1.3 inputs with Deep Colour(TM) support and auto/manual switching, 5.1 Dolby Digital/DTS sound, perfect image centering in both component and RGB modes, output resolution limiting, and user customizable options via DIP switches!
How does the HDfury3 compare to previous versions?
Feature HDfury1 HDfury2 HDfury3 Compatibility GOOD(Issues with some devices such as HDMI receivers & switchers) BETTER(Not compatible with Deep Color mode) BEST Data processor 10 bit, 175 Mhz 11 bit, 200 Mhz 11 bit, 225 Mhz Pixel clock bandwidth 165 Mhz 165 Mhz 225 Mhz Maximum Resolution supported 1080p/60 1080p/60 1080p/72 Number of Inputs One One Two Input Type DVI-D HDMI 1.1/1.2 HDMI 1.3 with Deep ColorTM support Output Type RGBHV only Component or RGBHV(user selectable) Component or RGBHV(user selectable) Long output cable support NO YES(25-35′ cable) YES!(40-50′ cable) User adjustable sync in RGB output mode NOThe H/V output sync matches the input sync NOThe H/V output sync matches the input sync YES!The H/V output sync may be forced positive or negative User selectable manual or automatic input switching N/A N/A YES! Sound Output NO YESLimited to 2-channel in both analog and digital YES!2-channel analog &Dolby/DTS 5.1 digital Image centering in component mode N/A YES, Automatic YES, Automatic Image centering in RGB mode NO NO YES!User adjustable RGB image centering via pushbuttons Colour Depth Upscaling NO YES(always on in all modes,not adjustable) YES!(user selectable in all modes) Lower power consumption NO YES(0.5A power supply) NO(1A power supply) Firmware upgradeable NO YES(by manufacturer only) YES(by manufacturer only) EDID upgradeable YES YES YES Screen position adjustable via firmware NO YES YES User selectable EDID banks NO NO YES!4 EDID banks (2 per input) User selectable output resolution limit settings NO NO(EDID must be reprogrammedby manufacturer or the user) YES!Two EDID banks are provided: One supports all resolutions, the other supports up to 1080i with 24Hz disabled(Both banks may be reprogrammed as well) Output resolution limit and custom profiling NO YES YES Technology 4 layer mid density class 5 PCB 6 layer high densityclass 5 PCB 6 layer high densityclass 5 PCB Ability to turn off the blue LED status light NO NO YES!For those who want 100% control over the light in their Home Theater The HDfury1 was RGBHV output only with a DVI-D input.
The HDfury2 introduced component (Y/Pb/Pr) output support with HDMI 1.1/1.2 input, colour depth upscaling to render 16-235 as 0-255, stereo sound output in both optical and analog, and supported third party accessories support on its output. The HDfury2 had an RGB output similar to the HDfury1 but with extended colour depth range for better colours.
For the HDfury3, the component features from HDfury2 were kept while the RGB and audio output were completely re-worked and improved. We are now extremely proud to announce that the LEFT SHIFT issue in RGB mode is NO MORE! The HDfury3 allows users to shift the picture LEFT/RIGHT at will through push buttons. The colour depth upscaling feature is now also user selectable (ON/OFF via DIP switch). The HDfury3 also features 4 customizable EDID banks, two of which may be used to limit the output resolution to 1080i out of the box (again via DIP switches). A very useful feature for anyone with a display that supports 1080i but not 1080p and has sources that do not offer manual setting of the output resolution. Also included are two HDMI 1.3 inputs with Deep Colour support and MANUAL or AUTO switching. Owners of fussy RGB displays will also be happy to learn that the H/V syncs may also now be force to either positive or negative via DIP switch. The RGB pixelclock bandwidth is greatly improved with 225Mhz support (1080p/72 is now perfectly resolved)!
HDfury3 main features:
- 2x HDMI 1.3 input with Deep Colour support (Manual or Auto switch mode available, user selectable)
- Component (YPbPr/YCbCr) and VGA (RGBHV) video output
- Sound output in both Analog and Digital Optical (S/PDIF 5.1 Dolby/DTS) through an innovative 3.5mm combo jack
- 4x EDID banks (2 per channel)
- Built-in user selectable output resolution limit settings
- Customisation settings available through DIP SWITCH
- Perfectly and automatically center image in all standard NTSC/PAL component modes
- Manually adjust horizontal screen position in all NTSC/PAL RGBHV modes
- Performs Colour Depth Upscaling in all modes (ON/OFF user selectable)
- Sync Polarity Inverter included
- Automatic SD/HD color-space selection
- Accept third party accessories on its output
- Improved output cable driver for driving long cable runs (40-50′)
- Software upgradeable
HDfury3 specifications:
- Input: 2 x HDMI v1.3 (DVI 1.0 compatible)
- Switch: Auto / PortA / PortB
- 10-bit deep color HDMI native support
- Output: VGA FEMALE output connector, 10 bit analog resolution.
- HDCP supported (Integrated HDCP decipher engine, Pre-programmed HDCP key)
- Horizontal shift capability for RGB output mode
- Enabled with a dip-switch, applied with push-buttons
- Output sync polarity selector for RGB modes (dip switch)
- Output format: Either RGB or YPbPr, dip-switch selectable
- YPbPr requires VGA->3RCA breakout cable
- All HD/SDTV formats from 1080p down to 480i, NTSC and PAL
- Including 1080p @ 72Hz PAL and NTSC (for RGB output only)
- Including 1080p @ 24Hz PAL and NTSC
- 11-bit 225MHz DAC processing (for true 10-bit analog output)
- Two separate Internal EDID EEPROM with complete CEA861 extension block
- Dip-switch selectable
- One EDID supports all formats
- The other EDID is up to 1080i, and no 24Hz support (by default, reprogrammable)
- Automatic Input Format Detection: Digital YCbCr and RGB
- Full BTB and WTW support in YPbPb output
- Automatically switches color-spaces for both HDTV and SDTV
- Precise black levels – no black crush in any standard mode
- Dual purpose audio output connector
- SPDIF digital output for 5.1 Dolby/DTS
- Analog L/R 2-channel stereo
- Industry-Standard Compliance
- HDMI 1.3
- EIA/CEA-861D
- DVI 1.0
- HDCP 1.1
- Digital Video Input / Output
- Dual integrated HDMI 1.3 cores
- Supports DTV resolutions up to 1080p @ 72Hz or 720p/1080i @ 120Hz with 36-bit color depth.
- Flexible digital video interface:- 24/30/36-bit RGB/YCbCr 4:4:4- 16/20/24-bit YCbCr 4:2:2- 8/10/12-bit YCbCr 4:2:2 (ITU-R BT.656)
- Integrated RGB Color Space Converter for both RGB-to-YCbCr and YCbCr-to-RGB (both 601 and 709) with true 12-bit accurate data using 14-bit processing
- 4:2:2 <> 4:4:4 converter with 12-bit accurate data using 14-bit processing
- Digital Audio Output
- Industry-standard S/PDIF output
- Supports 2-channel 32-192kHz stereo audio
- Supports IEC60958 2-channel PCM
- Capable of passing IEC61937 compressed audio (5.1 Dolby® Digital, DTS, etc.)
General:
Why do i need HD (720p) or Full HD (1080p)?
Blu-Ray players, HDMI graphic cards, PS3, Xbox 360 Elite are all able to unleash their true potential (720p/1080p mode) only through the HDMI output. If you want a valid ticket to the Full HD world you either need a compatible display (with HDMI input) or an HDfury3 for your existing display. 1080p FULLHD as found on Blu-ray and HD has over 6 times the resolution as standard DVD and TV. For the best movie and and home theater experience, you *need* Blu-ray/HD.
Why do i need a HDCP compliant display?
HDMI is a new standard that comes with a form of hardware protection called HDCP. If your display doesn’t have a HDMI input you won’t be able to display 720p/1080p signal on it (from HDMI sources). Prior to exchanging video data, the HDMI source exchanges HDCP keys with HDMI display. Both devices have a special HDCP chip embedded. If your display doesn’t include an HDCP chip, even if it’s technically able to display 720p or 1080p signal, it will display a BLACK SCREEN. On some devices (ex: Playstation3, Xbox360) 1080p mode is only available through the HDMI output.
I use component cables to connect my Blu-Ray or DVD player to my display device and it works just fine! Why do I need HDfury3?
Blu-Ray and many DVD players can also upconvert standard definition DVDs to higher resolutions (720p, 1080i, 1080p), but they only do this via the HDMI outputs (not component). So if you want to get the higher resolution benefits of your player’s upconversion circuitry, you’re forced to use HDMI. As well, in the future it may not be possible to pass certain high definition content over component video cables. A content flag called the ICT (Image Constraint Token) allows broadcasters and movie studios to limit or “down-res” the HD video signal to standard definition 480P resolution over component video cables. Hollywood has reportedly agreeed to not activate this flag until 2012. And the most important reason to use HDfury3: The picture quality is substantially better! (Sharper/cleaner/less noise/less ringing/etc). Talk to someone who uses one or read the reviews !
My picture ‘blanks out’ from time to time when using the HDfury3. Why is this happening?
If the HDfury3 blue LED is OFF during the picture blanking, the problem is with the HDfury3 or the power supply. We will replace them for you.
If the HDfury3 blue LED is ON during the picture blanking, the problem is with the the component cable, RGB cable or the display.
Lift the little panel found on the back of the HDfury3 and make sure that DIP switch 6 is set to ON. DIP switch 6 is used to turn the blue LED on/off, make sure it is set to ON if you are experiencing problems with your HDfury3. The blue LED will never come on if you have DIP switch 6 set to off.
Sound:
Do I need to use the sound output on the HDfury3?
Likely not. The audio output of the HDfury3 is a convenience feature if you do not have a home theater receiver. The HDFury3 supports stereo analog output as well as 5.1 Dolby/DTS digital SPDIF output. If all you have are the speakers in your TV you can use the 2-channel analog audio output of the HDfury3 as a covenient way to feed audio directly into your TV without having to run separate (possibly long) audio cables from the source to your TV as in many setups the HDfury3 will be plugged right into the TV. This way you only need to run one HDMI cable to the TV and then use a short audio cable from the HDfury3 to the TV sound input. Anyone with a home theater receiver/pre-amp and separate speakers should instead connect their source devices directly to the receiver/pre-amp and not use the HDfury3 sound output. You may use the 5.1 Dolby/DTS digital audio output of course if the positioning of your HDfury3 makes this more convenient. The choice is up to you! Typically there is no need to use the audio features of the HDfury3 with a home theater setup.
How do I hook up the audio from the HDfury3?
The HDFury3 has both analog and digital (TOSLINK) audio output in one connector located on the bottom of the unit labelled “D/A” along with a headphone symbol. It’s a 2-in-1 connector meaning that you can plug in either a 3.5mm stereo analog jack or a digital mini-TOLINK (3.5mm mini-jack) cable and get stereo analog sound or 5.1 Dolby/DTS digital sound out of the HDfury3. See further below for pictures of both types of connectors/cables.
HDfury3 3.5mm mini-TOSLINK digital audio cable:
If you’d like to use a “regular” TOSLINK cable, use a 3.5mm Mini-TOSLINK to regular TOSLINK adapter (not included):
A 3.5mm stereo audio cable (not included) is used for connecting the HDFury3 to a TV if you don’t have a home theater setup (you only have 2 speakers in your TV):
Inputs and switching:
How many inputs does the HDfury 3 have?
Two inputs, both HDMI 1.3 compliant with HDCP with support for Deep Color(TM). The HDfury3 is the first HDfury to support Deep Colour(TM).
How do I switch between the two inputs?
The switch on the side of the HDfury3 labelled “1A AUTO 2B” is used to switch inputs or to set the HDfury3 to switch automatically. To always use input 1A, set the switch to 1A. To always use input 2B, set the switch to 2B. To have the HDfury3 autoswitch, set the switch to AUTO.
How does the HDfury3 auto switching work?
The AUTO position will cause the HDfury3 to switch automatically to the source device with an active video signal. In the case of two active video signals whichever became active first will be chosen. The HDfury3 will then remain locked on that input until that source is turned off. In order words: If two sources are active and you wish to switch to the other, turn off the currently active one in order to switch to the other.
Video:
What resolutions does the HDfury3 support?
The HDfury3 supports any resolution/refresh rate combination (interlaced or progressive) up to 1080p/72Hz in RGB output mode, and 1080p/60 in component (YPbPr) output mode. 1080p/24 is also supported.
Does the HDfury3 change the resolution? Upconvert or downcovert?
The HDfury3 does not change the resolution or refresh rate in any way. It converts the HDMI 1.3 digital input signal to an analog RGBHV (VGA) or Component (Y/Pb/Pr) signal. It also provides HDCP decryption if needed. The HDfury3 outputs whatever resolution you feed it. Feed 1080p in and you’ll get 1080p out. Feed 480i in and you’ll get 480i out.
Does the HDFury3 support both Component and RGB video output? I thought they were the same?
The HDfury3 supports both component (Y/Pb/Pr or YUV) and RGBHV (sometimes called VGA) signal types on the output. They are not the same at all and cannot be used interchangeably . Some displays have component inputs, some displays have RGB, some have both. The HDfury3 lets you choose between the two to best match your display’s requirements.
My picture is all green! What’s going on?
You likely have a display that only accepts RGB and you have the HDfury3 set to component output (Y/Pb/Pr). Switch it to RGB.
I want to use the component input on my display. How do I set the HDfury3 to output component (Y/Pb/Pr) video?
Lift the little panel found on the back of the HDfury3 and set DIP switch 1 to OFF. Make sure to use the HDfury3 component breakout cable to connect the HDfury3 to your display’s component (Y/Pb/Pr) input. It is the cable with 3 RCA (phono) style connectors coloured red, green, and blue
I want to use the RGB (VGA) input on my display. How do I set the HDfury3 to output RGB (VGA) video?
Lift the little panel found on the back of the HDfury3 and set DIP switch 1 to ON. Make sure to use one of HDfury3 RGB cables to connect the HDfury3 to your display’s RGB (VGA) input. Three RGB cables are available: A VGA (D-Sub15) cable, a 5-BNC cable, and a special Barco CRT projector port 3 cable. Do not use the component 3 RCA (phono) style connector as it will not work.
I have a scaler or doubler with DVI/HDMI inputs and an RGB or Component output connected to my display device. I don’t need an HDfury3 right?
Not true. You still need the HDfury3 if you want to use HDMI sources such as Blu-Ray or DVD players as they use HDCP (high definition copy protection). The scaler is not allowed to output an analog RGB or Component signal. The scaler will simply TURN OFF its analog output or limit it to 480i resolution. Only the digital DVI/HDMI outputs will remain on. To solve this, connect the HDfury3 to the DVI/HDMI output of your scaler, and then connect the HDfury3 to your display device using the analog RGB or Component input. Simple!
I have a scaler or doubler with DVI/HDMI inputs and a DVI/HDMI output connected to my display device’s DVI/HDMI input. I don’t need an HDfury3 right?
Maybe. You still need the HDfury3 if you want to use HDMI sources such as Blu-Ray or DVD players that have HDCP-protected content *and* your display device only has a DVI input. The scaler, must pass the HDCP-protected content all the way to your display device. The display device must decrypt the content. If your display device only has a DVI input and it does not support HDCP, it will not be sent a signal. To solve this, connect the HDfury3 to the DVI/HDMI output of your scaler, and then connect the HDfury3 to your display device using the analog RGB or Component input. Simple!
I want to connect a longer cable to the output of the HDfury3. Can I do that?
Yes. The HDfury3 supports analog output cables up to 40-50 feet in length. The HDfury1 did not allow for longer output cables while the HDfury2 support cables up to 25-35 feet in length.
Does the HDfury3 support 24fps found in next generation Blu-Ray and HD DVD players?
Yes! While the HDfury1 does not, the HDfury2 and HDfury3 do support 24fps. With cathodic displays such as CRT projectors or CRT based RPTVs or tube TVs, 24fps is too low of a frequency for the display to use. The image will flicker like crazy and will not be watchable. You must turn off 24fps support in the source when using a CRT based display. You can however use 24fps on a plasma or LCD display and it will be displayed nicely using the HDfury3! Note however that most displays that do not have HDMI inputs will not work at 24 Hz as 24 Hz support was generally added to displays after HDMI was invented. To turn off 24 Hz, set your source devices to 50 or 60 Hz output and not 24 frames (Hz) or “Automatic”.
I can only get lower resolutions to work. When I set my source to high resolutions like 1080p I don’t get an image!
(1) Make sure to use the included HDfury3 power supply at all times. It is required at all times.
(2) Many TVs do not support 1080p and must be fed a 1080i or 720p signal instead. Make sure to set your source to 1080i or 720p unless your display’s manual specifically states that it supports 1080p.
(3) Make sure to turn off 24fps (24p) support in the source (see last question).
The picture is blank! I don’t get an image at all from my PS3, Blu-ray player, or other source!
(1) Make sure your display supports the resolution the source is feeding it. If your TV does not support 1080p, set your sources to 1080i or 720p. Some sources will automatically use the highest resolution available to them based on what they see connected, and since they see the HDfury3 which supports 1080p FULL HD, the source will ‘think’ you have a 1080p capable TV and is most likely feeding the HDfury3 a 1080p signal. You need to lower this to 1080i or 720p in the source device.
(2) Make sure that the 24fps output option in the source device is set to OFF or DISABLED and not AUTOMATIC unless your TV specifically supports 24fps. Most do not, especially older TVs that do not have HDMI inputs.
(3) Make sure you’re using the HDfury3 power supply at all times.
I’m still getting a black screen from my PS3 when using the HDfury3. How can I fix this?
The problem is that